Chief PXR Bedienungsanleitung

INSTALLATION INSTRUCTIONSAutomated Wall MountThis device complies with part 15 of the FCC rules. Operation is subject to the following 2 conditions: (

PXR Installation Instructions101. Using a stud finder, locate and mark the two 16" on center2" x 4" wood studs to which the PXR will be

Installation Instructions PXR118. Mark the pilot holes through PXR upper bracket. (SeeFigure 7)9. Carefully remove the PXR from the mounting bracket.1

PXR Installation Instructions12WARNING: INSTALLING THE PXR IN UNDERRATED ORDAMAGED CONCRETE CAN LEAD TO SERIOUS INJURYOR DAMAGE TO PRODUCT! When insta

Installation Instructions PXR138. Mark the pilot holes through PXR upper bracket. (SeeFigure 13)9. Carefully remove the PXR from the mounting bracket.

PXR Installation Instructions14The following procedure assumes that a Chief Listed ModelPAC502 In-Wall accessory (not included) has previously beenins

Installation Instructions PXR157. Carefully lift up and out slightly on bottom of PXR. (SeeFigure 21)8. Route power cord and cables through cable mana

PXR Installation Instructions161. Carefully pull arms out from wall. (See Figure 24)2. Open cable management covers on bottom of PXR arms.3. Engage PX

Installation Instructions PXR17Installing IR Sensor1. Plug IR receiver (AA) into PXR. (See Figure 3) and (SeeFigure 26)2. Route IR receiver to desired

PXR Installation Instructions18• LEARN MODE Phase APhase A of the LEARN MODE helps the PXR"learn" the amount of resistance in the installati

Installation Instructions PXR19CAUTION: THE INTERFACE BRACKETS ATTACHED TOTHE DISPLAY MUST BE THE FURTHEST POINT OFPROTRUSION FROM THE DISPLAY BACK. I

PXR Installation Instructions2DISCLAIMERMilestone AV Technologies, and its affiliated corporations andsubsidiaries (collectively, "Milestone"

PXR Installation Instructions202. Lock display with attached interface brackets to PXR usingtwo bracket locks (W) and four 1/4-20 x 1/2" hex head

Installation Instructions PXR215. Open cable management covers on bottom of both PXRarms and lay cables within arms. (See Figure 34) and (SeeFigure 37

PXR Installation Instructions22CAUTION: ENSURE INTERFACE BRACKETS ARELOCKED TO THE PXR RAILS BEFORE BEGINNINGLEARNING MODE! The display must be center

Installation Instructions PXR233. Add plastic covers (P) to PXR, fastening with two8-32 x 1/4" Phillips flat head screws (S). (See Figure 41)Figu

PXR Installation Instructions24PROGRAMMING VIA RS485Setting PXR AddressNOTE: If multiple PXR’s or Chief automated products will becontrolled in the sa

Installation Instructions PXR25Common CommandsThe PXR ships with the default address of 00 (all I/O DIPswitches set to "Off").The PXR has a

PXR Installation Instructions26Get System Status (0x2F)Command MessageStatus Response with Position DataExample of how to get the blink code status of

Installation Instructions PXR27Chief Part Number: 7000-002052Carrier Frequency: 38KHzProtocol: NEC - Full RepeatSystem Code(s): 6E (Default) - Multipl

PXR Installation Instructions28RS-485 Terminal Block WiringFigure 48Terminal Block Manufacturer: Molex (See Figure 48)• Terminal Block Manufacturer P/

Installation Instructions PXR29

Installation Instructions PXR3TABLE OF CONTENTSDISCLAIMER . . . . . . . . . . . . . . . . . . . . . . . . .2TABLE OF CONTENTS . . . . . . . . . . . .

PXR Installation Instructions30

Installation Instructions PXR31

PXR Installation InstructionsUSA/International A 8401 Eagle Creek Parkway, Savage, MN 55378P 800.582.6480 / 952.894.6280F 877.894.6918 / 952.894.6918E

PXR Installation Instructions4DIMENSIONS16.00406.420.45519.545° PAN LEFT 45° PAN RIGHTMAX. HORIZ. PATTERN700.0469.918.50252.2TO CENTER487.219.189.9345

Installation Instructions PXR5DIMENSIONS...continued29.50749.37.38187.310.70271.812.15308.512.40315.04.88123.85.10129.5ARMS AND HEAD UNIT HIDDEN FOR C

PXR Installation Instructions6LEGENDTighten FastenerApretar elemento de fijaciónBefestigungsteil festziehenApertar fixadorSerrare il fissaggioBevestig

Installation Instructions PXR7TOOLS REQUIRED FOR INSTALLATIONPARTS7/32" (5.5mm) - wood#21/2" (12.7mm) M55/16" (8.0mm) - concr

PXR Installation Instructions8SITE PREPARATIONLocating and Preparing a Mounting SiteThe PXR was designed to be installed onto a 16" on center2&qu

Installation Instructions PXR9PXR DIAGRAMFigure 3RailsInterfacebracketInterfacebracketIR Repeater(cable not included)Output at 38kHz3.5mm mono plug6 P